|
LEE
POWDER MEASURES
Lee Auto-Disk Powder Measure
|
Lee Pro Auto-Disk Powder Measure
|
| Auto-Disk Powder Measures automatically dispense charges more uniformly than any other powder measure. The case itself actuates the measure as the neck is being flared. The measure is actuated during the presses maximum mechanical advantage. This assures the smooth, even action of the measure. Built-in baffle and precisely molded, glass reinforced charge disks contribute to the unmatched charge uniformity. Includes all four disks! |
Commercial reloaders
or competitive shooters first choice! Elastomer wiper and teflon
coated metal casting make this the smoothest operating measure.
Will not cut powder and almost totally
eliminates leakage. Large hopper with shut-off valve is attached
with brass thumb nuts for the ultimate in disk changing convenience.
Increased safety with positive pull-back lever. Includes swivel
adapter and spring return lever with spring. Includes all four
disks! |
Auto-Disk Powder Measure 
90578
30.98 |
Pro Auto-Disk Powder Measure
90429
47.00 |
NOTE:
The Auto Disk powder measures must be used with the powder through
expanding die supplied with all Lee pistol dies. These dies may
be purchased individually for $12.98. See listing of dies on Pistol
Dies page.
  Lee
Auto-Disk Riser
The Lee Auto-Disk Riser allows use of other brands
of dies that have extended adjusting screws and provides clearance
for the Lee Safety Prime.
| Lee Auto-Disk Riser |
90041 |
9.98 |
|
Lee Rifle Charging Die
This die is used to charge small capacity rifle cases using the Auto-Disk Powder Measure. It works the same as the pistol powder through expanding dies except it doesn't expand the case mouth. Rifle case expansion is normally done in the sizing die.
Lee Rifle Charging Die 90194
11.98 |
|
Adjustable Charge Bar
Infinitely adjustable between .28 and 1.6 cc. Lifetime nylon with solid brass, zero backlash micrometer. Easy to set.
Lee Adjustable Charge Bar90792
9.98 |
|
Micro Disk
Accurately measures small charges below the range of the standard Auto Disk Powder Measure. Six cavities range from 1.1 to 2.5 grains of Bullseye. This is an ideal kit for small caliber cases and light target loads. Can be used on the Auto-Disk or Pro Auto-Disk Powder Measures.
Micro Disk and Spacer 90302
9.98 |
|
Double
Disk Kit (not
pictured)
This kit raises the hopper so you can stack two disks. This not only doubles the capacity of the disks but it makes very fine adjustments possible. Most powders can be adjusted up or down .1 grain with different combinations of disks. Complete listing of combinations, 4 extra disks, screws and risers are included.
Lee Double Disk Kit90195
14.98 |
Pro Auto-Disk Update Kit |
Auto Disk Pull Back Lever |
Swivel Adapter |
|
|
|
| Update any Lee Auto-Disk Powder Measure with all the PRO features, except for the teflon coating. Includes oversize hopper and valve assembly with elastomer wiper, swivel adapter assembly for fast and easy transfer between die sets, pullback lever, chain and attachments, solid brass knurled thumb nuts. With FREE adjustable Charge Bar. |
Pullback lever for progressive reloading. Eliminates the possibility of powder binding while reducing the chance of missed or double charges caused by operator error. |
For fast and easy transfer between die sets. Screws into your die without rotating the measure. Allows precise positioning with firm clamping.
|
| Pro Auto-Disk Update Kit 90377
19.98 |
Pull Back Lever and Chain90479
2.98
|
Swivel Adapter90477
5.98 |
 |
Lee Powder Measure Kit
Fifteen uniformly graduated and proportioned powder dippers. Slide card shows the grains of powder each measure will dispense of every type of powder.
Powder measures are inherently safe as they cannot get out of adjustment. That's why powder dippers continue to be the first choice of reloaders who load in small quantities.
|
| Lee Powder Measure Kit |
90100 |
10.98 |
Powder Funnel
A large, unbreakable funnel that fits all cases from .22 to .45 caliber. Hole in flange permits mounting to the Lee Turret Press, shelf or bench. |
|
| Powder Funnel |
90190 |
2.98 |
See
What One Satisfied Customer Has To Say About The Auto
Disk Powder Measure!
Dennis O. from
East Peoria, IL:
I
just want to say thank you for your fine line of
reloading equipment. I usually don't write letters like
this but I had to let you know how much I appreciate the
reloading tools of Lee. Like so many others I started out
with the Lee Loader, but now have moved up to one of your
bench mounted presses with Lee dies, Auto-Disk Powder
Measure and other Lee tools and accessories. The
Auto-Disk Powder Measure is by far the best piece of
reloading equipment for reloaders since the invention of
the press itself, and now with the introduction of your
new neck sizing dies, you've done it again. Several of
these dies will be on my reloading bench very shortly.
I
don't know what new products Lee will introduce in the
months and years ahead but it's safe to say it will be
part of my reloading bench. All this at a very affordable
price. Lee, the innovative leader, how true that is. Keep
up the good work.
|
Request paper catalog 90495