The bullet seater plug that comes with the die set is as close to generic as we can make it. If you find that the bullet seater plug deforms the nose of the bullet you are trying to seat, we can make a custom bullet seater plug to fit your bullet.

We need:

1. Payment of $12.00 ($8.00 + $4.00 processing fee)
2. 1 sample bullet

The carbide handgun 3-die set consist of a carbide sizing die, which requires no case lubrication, a powder through expander die and a seater crimper die. This option is applicable only for calibers that have straight walled case design. The range would be from as small as the .25 ACP to the 480 Ruger.

We need:

1. Payment of $272.00 ($230.00 set-up charge + cost of the dies $38.00 + $4.00 processing fee)
2. 5 fired cases
3. 3 bullets or cartridge and chamber dimensions

Lead time on these sets can be as long as 180 days as a new carbide ring must be made and ground for your cartridge.

The set-up charge is a one time per order charge, therefore additional die sets of the same caliber requested in the same order bear only the applicable cost of the dies. If 25 die sets are ordered at one time, we waive the set-up charge.

Also see Full Length Die Set and Steel Die Set

Custom case length gauges can be made for cartridges that fit an existing shell holder. A list of calibers and their corresponding shell holders can be found in our catalog (page 24) or on the FAQ portion of our website under "Case Preparation" and then "Shell holders and calibers." While there is really no maximum caliber, the smallest we can make is .22.

We need:

1. Payment of $19.00 ($15.00 + $4.00 processing fee)
2. Desired trim length
3. Bullet diameter or a couple sized sample cases
4. Shellholder number

Please allow five weeks for delivery.

A Custom Collet Die Set consists of the Collet sizer and the Dead Length Bullet Seater, a shell holder and dipper. Maximum outer diameter at the base is .555 and the maximum bullet diameter is .375. There are a few exceptions for the larger Ultra Mags and if interested in those, you may want to give us a call or send a case to determine whether or not we can make them.

We need:

1. Payment of $54.00 ($50.00 + $4.00 processing fee)
2. 2 fired cases from the rifle that the ammunition is to be reloaded for
3. 2 sample bullets

Lead time on Collet dies is approximately 90 days depending upon our work load.

We need:

1. Payment of $154.00 ($150.00 + $4.00 processing fee)
2. 2 fired cases
3. 2 sample bullets

RIFLE:

A Custom Factory Crimp Die for rifle cartridges can be made for any cartridge with a bullet diameter up to .458 inch and a maximum outer diameter at the base of .580.

We need:

1. Payment of $29.00 ($25.00 + $4.00 processing fee)
2. Dummy cartridge (a bullet seated in an empty case)

Rifle Factory Crimp Dies are cartridge specific and there are a few that cannot be made. Any handgun case that is of a bottleneck design qualifies because the die would have to made much like the rifle factory crimp dies but we do not make die bodies shorter than that you would find on a .223 Remington. Examples would be the 30 Mauser, 7.62 x 25 and the .357 Sig. The 50 AE also applies because the case is too short for the die bodies available.

PISTOL:

Custom Carbide Factory Crimp Dies for handgun cartridges can be made for most handgun cartridges that are not in regular stock. Sizes available run from 25 ACP sized cases up to the 480 Ruger. The 50 AE cannot be made because the carbide ring necessary for this cartridge is too large for our manufacturing process.

We need:

1. Payment of $34.00 ($30.00 + $4.00 processing fee)

1 1/4 x 12" Thread

We need:

1. Payment of $79.00 ($75.00 for the die set + $4.00 processing fee)
2. Bullet seated in an empty case

PISTOL:

Full length 3-die set includes the full length sizing die, bullet seating/crimper die, and the powder thru expanding die.

We need:

1. Payment of $192.00 ($150 setup fee + $38.00 for the die set + $4.00 processing fee)
2. 5 fired cases
3. 3 sample bullets

Carbide full length 3-die set includes the full length carbide sizing die, bullet seating/crimper die, and the powder thru expanding die.

We need:

1. Payment of $272.00 (Setup charge $230.00 + $38.00 for the die set + $4.00 processing fee)
2. 5 fired cases
3. 3 sample bullets

We waive the set up charge if 25 or more of the same caliber die sets are ordered at the same time. Dealer and Distributor discounts will apply on orders of 100 pieces or more.

Please allow about 180 days to complete.

Maximum bullet diameter is .575.

We need:

1. Payment of $29.00 ($25.00 + $4.00 processing fee)
2. Desired diameter to the factory

Please allow 4 weeks for delivery.

We make custom bullet molds to your specifications. Maximum bullet mold dimensions for standard mold blocks; (all dimensions in inches) single cavity, .580 diameter, 1.250 length; double cavity, .685* diameter, .900 length; six cavity, .520 diameter, 1.000 length; *for single cavity mold in double cavity blocks, like our slug mold. For two cavities in the double cavity blocks, max. diameter is .600 inch. Click here for a mold design assistance sheet.

We need:

1. Payment ($100 set-up and tooling fee for flat based bullets plus the cost of the mold ) ($150 for hollow based bullets, plus the cost of the mold)
2. Single or double cavity molds would be $24.98 each, six cavity would be $50.00 each. Hollow base bullets can only be made in single cavity, and are $25.98 each.
3. Add $4.00 to your order for order processing fee

The above set-up and tooling fee will be waived on orders of 25 pieces or more. For orders over 100 pieces regular dealer/distributor prices apply to mold prices, in addition to elimination of the set-up and tooling fee.

Three die handgun steel die sets consist of a steel sizing die (requires case lubrication), a powder through expander die and a seater crimper die. Generally, this option is chosen for calibers that have a design other than straight walled because carbide is not practical for such designs.

We need:

1. Payment of $192.00 ($150.00 setup charge + cost of dies $38.00+ $4.00 processing fee)
2. 5 fired cases
3. 3 bullets or cartridge and chamber dimensions

The setup cost is a one time per order charge, therefore additional die sets of the same caliber requested in the same order bear only the applicable cost of the dies. If 25 die sets are ordered, we waive the setup cost.

Please allow about 180 days to complete.

Two die rifle sets consist of a steel sizing die (requires case lubrication) and a seater crimper die.

We need:

1. Payment of $172.00 ($130.00 setup charge + cost of the dies $38.00+ $4.00 processing fee)
2. 5 fired cases
3. 3 bullets or cartridge and chamber dimensions

Full Length Sizing Die Only - setup charge is $100.00 plus $15.00 for the cost of the die. Allow 90 days for delivery.

The setup cost is a one time per order charge, therefore additional die sets requested in the same order bear only the applicable cost of the dies. If 25 die sets are ordered, we waive the setup cost.

Please allow about 180 days to complete.